Product Quick Search
     
 
 Product Literature

Conveyor CatalogClick here to view product catalog in PDF format.

Click here to receive a copy of our current conveyor & conveyor accessory catalog.

 
 Knowledge Base
 

Bearing Basics
Belt Lacing Instructions
Belt Tracking
Belt Replacement Guide
Belt Selection Guide
Conveyor Maintenance
Drive Chain Tensioning
Glossary - Conveyor Terms
Gravity Conveyor Basics

Click here
to learn
more
about our
Plastic
Belt
Conveyors

 
 
 
 

Subscribe to our Newsletter!
View Newsletter Archive

 
 
   

Search for:

 

 
 
 Belt Driven Conveyor Products
MODEL BDLR19
 BELT DRIVEN LIVE ROLLER CONVEYOR 1.9" DIA., 16 GAUGE ROLLERS

 

  Catalog Sheet

 

The BELT DRIVEN LIVE ROLLER CONVEYOR provides minimum pressure accumulation with rollers on close centers. The BDLR can provide variable accumulation pressure by adjusting the tension rollers as required.

Roll your pointer over the numbers
to view the feature description.

 

  Carrier Roller: 1.9 dia., 16 ga. wall tubes with 7/16 hex cold rolled steel axle, spring retained. Standard A11 bearings are greased packed.
Roller Centers: 2.00”, 3.00”, 4.00”, and 6.00”.
Tension Roller Centers: Always two times the carrying roller center. Example: 3” centers – pressure roller centers would be 6” centers. Pressure rollers are mounted in adjuster plates for adjusting the pressure exerted on the carrying rollers above.
Belting: Standard B06 PVC-120 black, friction surface. Belt is shipped laced and installed on conveyors up to 10’ long. On all other conveyors the belt is shipped loose with lacing installed for field installation.
Between Frame: Standard 15”, 19”, 21”, 25”, 27”, 33”, 37”, and 39”. Also available from 6” to 39” in even 1” increments.
Belt Width: 6” wide on 13” through 39” between frames.
Lengths: 5’ to 100’ in even 1” increments.
Drive: Standard D02 - center, right hand side. Drive has cast iron worm gear speed reducer with standard M99 1/2 H.P. 230/460 volt TEFC Motor.
Speed: Standard 60 feet per minute. Also available from 10 to 120 fpm.
Bearings: Sealed Pre-lubricated, cast iron flange ball bearings.
Frame: 7-1/4” x 1-1/2” x 1/8” formed steel channels with bolted 2” x 3/16” galvanized angle lower cross ties and bolted 1 1/2 x 1/8” angle upper crossties.
Drive Pulley: Standard 8” dia. with 1-7/16” dia. shaft crowned and lagged. Mounted in 2 bolt flange bearings. Note: Used on D02 & D03 drive options also on conveyors 51’ and longer. 4” dia. with 1-3/16” dia. shaft crowned and lagged, mounted in 2 bolt flange bearings. Used on all other conveyors.
Take-up Pulley: 4” dia. with 1-3/16” dia. shaft, crowned and lagged, mounted in 2 bolt flange bearings. Used on all other conveyors.
Snubber Rollers: Standard 2.5 dia. 11ga. wall tubes with 11/16” hex cold rolled steel axle, spring retained. Standard A55 bearings are greased packed with front and back seals. Used on conveyors with D02 & D03 center drive. 1.9” dia. 12 ga. wall tubes with 7/16” hex cold rolled steel axles, spring retained. Standard A23 bearings are greased packed with front and back seals. Used on all other  conveyors.
Tension Rollers: 1.9 dia., 16 ga. wall tubes with 7/16 hex  cold rolled steel axle, spring retained. Standard A11 bearings are grease packed. The same for return rollers.
Capacity: 200 pounds per lineal foot. Total load not to exceed capacity shown in chart.
Supports: SPHH Style adjustable set for a standard 36” top of roller located on nominal 10’ centers. Also available from 7.5” to 42” top of roller at no additional charge.
Roll Covers: Standard V98: No Roll Cover
Finish: Standard PP94: Safety Blue, Epoxy Powder Coat.
 
 

OPTIONAL COMPONENTS
(Click for description)

BELT

B06; B25
DRIVE D02; D01; D03; D04; D05; D08; D41; D44; D45; D46; D99
MOTOR M99; M01; M02; M04; M05; M06; M07; M08; M09; M10; M11; M12; M13; M14; M15; M16; M27; M31; M32; M33; M34; M98
ROLLER BEARING A31;  A11; A13; A18; A21; A23; A33
ROLL COVER V98; V41
SUPPORT CENTER SCC10; SCC5; SCC0
FINISH PP94; PP09; PP11; PP24; PP45; PP95; PP99

 

HOW TO ORDER

BDLR19 - BF - RC - LG - SP - BE - EE- BELT - DRIVE - MOTOR - ROLBRG - ROLCV - SUPCC - FINISH

EXAMPLE: BDLR19 - 15 - 3 - 120 - 60 - 36 - 36 - B98 - D02 - M99 - A11 - V98 - SCC5 - PP94

 


 

   
   
  Product Catalog | Site Map | Contact Us | Gravity | Powered | Accessories | Systems | Parts & Service | About Us

706 Lane Street | Sandusky, OH 44870
Sales: 419-625-4014 | Fax: 419-625-1247 | Email: sales@lewcoinc.com

Copyright (c) 2005 LEWCO, Inc. All rights reserved.