Belt Driven Live Roller Conveyor by LEWCO, Inc. Model BDLN25

Product Quick Search

Product Literature


Click here to view product catalog in PDF format. Click here to receive a copy of our current conveyor & conveyor accessory catalog.

Knowledge Base

Bearing Basics
Belt Lacing Instructions
Belt Tracking
Belt Replacement Guide
Belt Selection Guide
Conveyor Maintenance
Drive Chain Tensioning
Glossary - Conveyor Terms
Gravity Conveyor Basics

Click here
to learn
more
about our
Plastic
Belt
Conveyors

Subscribe to our Newsletter!
View Newsletter Archive

Belt Driven Conveyor Products

MODEL BDLN25
BELT DRIVEN LIVE ROLLER CONVEYOR 2.5" DIA., 11 GAUGE ROLLERS

Catalog Sheet

Roll your pointer over the numbers
to view the feature description.

Carrier Roller: 2.5 dia. 11 ga. wall tubes with 11/16 hex cold rolled steel axle spring retained. Standard A51 bearings are grease lubricated.
Roll Centers: 3.00”, 4.00”, and 6.00”
Tension Roller Centers: Always two times the carrying roller center. Example 3 “ centers - pressure roller centers would be 6” centers. Pressure rollers are mounted in adjuster plates for adjusting the pressure exerted on he carrying rollers above.
Belting: Standard B06 PVC-120 black, friction surface. Belt is shipped laced and installed on conveyors up to 10’ long. On all other conveyors the belt is shipped loose with lacing installed for field installation.
Between Frames: Standard widths are 13”, 15”, 17”, 19”, 21”, 23”, 25”, 27”, 31”, 33”, 37”, 39”. Also available from 6” through 39” in 1” increments.
Belt Width: 6” wide on 13” through 21” between frame, 18” wide on 21” through 39” between frame.
Lengths: 10’ to 100’ in 1” increments.
Drive: Standard D46 located below Bed rollers on right side. Drive has cast iron worm gear reducer with standard M03 3/4 H.P. 230/460 volt TEFC motor.
Speed: Standard 30 feet per minute. Also available from 10 to 120 fpm. Bearings: Sealed pre-lubricated, cast iron flange ball bearings.
Frame: 11” x 1-1/2” x 3/16” formed steel channels with bolted 2” x 3/16” galvanized angle lower cross ties and bolted 1-1/8” x 1/8” angle upper crossties.
Drive Pulley: 8” dia. With 1-7/16” dia. Shaft crowned and lagged. Mounted in 2 bolt flange bearing.
Take-up Pulley: 4” with 1-3/16” dia. shaft, crowned mounted in 2-bolt flange bearing.
Snubber Roller: 2.5 dia. 11 ga. wall tubes with 11/16” cold rolled steel axle, spring retained. Standard A55 bearings are greased packed with front and back seals.
Tension Roller: 1.9 dia. 16 ga. wall tubes with 7/16” hex cold rolled steel axles, spring retained. Standard A11 bearings are grease packed. The same for return rollers.
Capacity: 1000 pounds per lineal foot of conveyor. Maximum 4000 pounds unit load. Total conveyed load not to exceed capacity shown in chart.
Supports: SPHH style adjustable set for standard 36” top of rollers located on nominal 5’ centers. Also available from 12” to 13.25” top of roller at no additional charge.
Roller Covers: Standard V98: No roller cover.
Finish: Standard PP94: Safety Blue, Epoxy Powder Coat

OPTIONAL COMPONENTS (Click for description)
BELT	B25; B06
DRIVE	D46; D47; D99
MOTOR	M03; M01; M02; M04; M05; M06; M07; M08; M09; M10; M11; M12; M13; M14; M15; M16; M27; M31; M32; M33; M34; M98
ROLLER BEARING	A51; A53; A55; A60
ROLL COVER	V98; V73
SUPPORT CENTER	SCC5; SCC10; SCC0
FINISH	PP94; PP09; PP11; PP24; PP45; PP95; PP99

HOW TO ORDER

BDLN25 - BF - RC - LG - SP - BE - EE- BELT - DRIVE - MOTOR - ROLCV - SUPCC - FINISH

EXAMPLE: BDLN25 - 15 - 3 - 120 - 30 - 36 - B06 - D46 - M03 - A51 - V98 - SCC5 - PP94

706 Lane Street | Sandusky, OH 44870
Sales: 419-625-4014 | Fax: 419-625-1247 | Email: sales@lewcoinc.com